First, the remote control configuration 1. Clear the operation (that is, remote control switch initialization): in the lamp is off state, long press the remote control switch any button for more than 10 seconds, the light from the light to the release and then release (clear operation is complete). 2. The first switch remote control configuration: press the first remote control switch on the hand control key, to be loaded lights lit and let go. And then press the manual key for about 3 seconds, to the load light from the off to light, and then let go, then remote control switch into the learning state, press the remote control on any one button, launch control signal; learning After successful, the load fixture will turn from light to off. 3. Specific operational procedures: press the manual key ---- light ---- release ---- and then put down ---- lights off ---- for 3 seconds ---- lights - - and then release ---- press the remote control key ---- 2 seconds ---- lights off ---- learn to complete; if not remote control, please repeat the above operation; 4. According to the above steps, configure the remote control keys; 5. Add the remote control: repeat the above steps, you can learn up to 12 remote control. More than 12, the first one is deleted.
Second, the operation method 1. Manual control: press a button on the switch, then the corresponding light, then press the light again. 2. Remote control: press the above learning good remote control button, the corresponding light, then press the light again. 3. With the total open function (only twelve keys of the remote control): When learning the 12 key remote control, the default 11 key is fully open, the first 12 keys for the whole off;
Third, the product features 1. Single fire line control, direct replacement of the original wall of ordinary mechanical switch, do not change any line. 2. Using imported original Omron high-grade relay, longer service life. 3. The use of pure copper wiring column, easy wiring. 4. Using intelligent MCU system, users more convenient remote control of the matching. 5. Ultra-low standby power consumption, standby light flicker when the phenomenon. 6. With over-current over-voltage protection, and in the anti-interference has a very good performance. 7. Compatible with starter-type fluorescent lamp, do not have to connect capacitance and other accessories. 8. Power-on time is short, energy-saving lamps about 1 second, starter-type fluorescent lamp about 2-3 seconds; 9. Using multi-channel power supply technology, standby power consumption is smaller, and, regardless of power supply primary and secondary. Effectively avoid the destruction of a road and lead to the entire product can not use the situation. 10. With power-down self-recovery function. Recovery time <2 seconds; Fourth, technical indicators Operating voltage: energy-saving lamps AC125V-AC250V 50HZ / 60HZ starter lamps AC180-250V; (need to use 110V power supply can be customized) Load power: 450W (resistive) 200W (perceptual) Capacitive load less than 150 watts; Power up time: 1-2 seconds Remote control frequency: 315M (can be customized for other frequencies) Remote control distance: measured space> 50 meters; Standby current: access to the load (energy-saving lamps), measured about 80UA single about two, about 40UA two, three less than 30UA; Fifth, note 1. Installers need professional electrician personnel. Although the installation is extremely simple, but the proposed professional staff to carry out. 2. Do not install live. The power must be switched off before installation to prevent electric shock. 3. Do not connect the FireWire to the zero line to the product; otherwise it will cause the product to burn. 4. This product is suitable for all kinds of lamps (bulbs, energy-saving lamps, fluorescent lamps, etc.); some with a condenser starter (fake Philips brand starter) may lead to not work, please replace the normal without capacitance Only a neon bubble) of the starter can be; 5. Do not overload the use of the emotional load power greater than two hundred watts, may cause excessive heat, resulting in abnormal work. At this point, please reduce the load, and then put into use; 6. In normal use, such as the remote control is lost, in the purchase of remote control, the need to specify the code IC is 2262, the oscillation resistance of 4M7 remote control; such as the remote control IC is 2260, please oscillating the resistance to 10M. Buy back the remote control according to the above (remote control configuration) for learning configuration can be put into use;
