Shenzhen Chenjie Electronics Co., Ltd. design and manufacture of multi-functional wireless intelligent receiver controller, mainly used in lighting, electric doors, windows, lifting equipment, gate, lifts, industrial control and security industries and other fields. The wireless receiver controller, with high confidentiality, stable performance, low power consumption characteristics, and easy to use, just the remote control of the wireless signal sent to the receiving controller to receive and store, you can achieve supporting the use. The controller can learn 16 remote control. Its output mode, respectively, there are three self-locking, jog, interlock. product description
220v2 learning remote control function Description:
One: line access and determine the output mode 1, the input is marked as L, access to FireWire. 2, the input marked as N, access to the zero line. 3, on the board marked 1,2,3 for a group of three relay output, respectively, corresponding to NC, COM, NO. (Output for the switch signal); 4, on the board marked 4,5,6 for the other three sets of relay output, respectively, corresponding to NC, COM, NO (output for the switch signal); 5, set the output mode: JP2 position on the board jumper cap, power plug before plugging. After the jumper cap is inserted (as described in 6, 7, 8), the output status is determined. (Note: the output state is determined before power-on, change the jumper after power-on, will not change its output function) 6, set the output mode: jog! Jumper to 1,2 end (short the two ends), the output mode is instantaneous (jog); specifically: press the remote control button, the relay to pull, release the remote control button, the relay release. 7, set the output mode: self-locking! (Self-locking); Specifically: press the remote control button, the corresponding group of relay pull, then click the remote control button, corresponding to the remote control button The relay is disconnected; 8, set the output mode: interlock! Jumper pull out, do not; output mode: interlock, specifically: press the remote control A button, the first group of relay pull, press the remote control B button, the second group of relay pull, the first group of relay off Open, two sets of relays are presented interlocking state. Press the C button, both sets of relays are disconnected.
Second: learning to code and clear 1, according to the above connected to the line and determine the output mode, the need to learn through the code, in order to use the remote control for the correct control. 2, please follow the steps below, step by step. 3, in the control panel has a S1 touch switch, this button is used to learn the code and clear the use. 4, clear: before learning the code, you need to clear the operation. The specific operation is: press S1 do not put, see the LED point light, do not let go, until you see the LED flashing, it OK. The clean operation is complete. 5, learning to the code: the code is based on different output status to the corresponding. If the output mode is jogging or self-locking, then just use two remote control buttons to control it, so only two buttons are learned. If the output mode is interlocked, then you need to learn three different remote control buttons to control it. Here it is divided into two different ways to learn. Jogging and self-locking learning is the same way that interlocking learning is different from them. (1): the output for the jog and self-locking study of the code: press S1, see the LED lit after the release of S1, this time has entered the learning state, within five seconds to complete the following steps, press the remote control (The button will control the first road after learning), see the LED flashing 2, and then continue to press the second button on the remote control (the button will be finished after learning the second road), see The LED flashes four times and goes off. Learning finished. If learning is unsuccessful, repeat steps 4,5. (2): the output mode for the interlocking study of the code: press S1, see the LED lit and release S1, this time has entered the learning state, within five seconds to complete the following steps, press the remote control 1 button (the button will be finished after learning the first road), see the LED flashing 2, then press the second button (the button will be finished after learning to control the second road) to see the LED flashing 3, then Press the third button of the remote control (the button after learning the function is to turn off two), LED flashing 4 off. Learning finished. If learning is unsuccessful, repeat steps 4,5. 6, the product is multi-functional type, wide use, due to more features, the operation need to step by step. Moreover, you can repeatedly clear the study. 7, we must pay attention to safety, then the line power, the board with a strong power! The The After power can not touch the metal parts on the board, the operation (except for remote control), the human body to ensure good isolation with the ground! Moreover, the input must have a leakage protection switch can be used. Wish you to use this product happy!
